The framers are done, the trusses are set and the sheathing is getting rained on while the schedule slips. Metal Roofing in Bucks connects Fallbrook builders and homeowners with independent local roofers who handle Roof Installation on new framing, additions, garages and sunrooms. Call once and get routed to a licensed and insured contractor who can plan dry-in around your framing and inspection dates.
There is nothing to tear off on a new build, but there is a lot more to coordinate. The sheathing has to pass a nailing inspection in many jurisdictions before anything covers it, the windows and siding crews are waiting on a dry box, and the electrician wants the attic closed in. If the roofer shows up a week late, OSB that has sat through a few rains can swell at the edges and leave ridges you will see through the shingles.
Additions bring a different headache. The new roof has to meet an old one, and the seam where they meet is where most addition leaks start. A garage roof that dies into a second-story wall needs step flashing woven behind the siding, a kickout flashing at the bottom and sometimes a cricket. A sunroom with a shallow pitch may not even qualify for shingles.
Expect the local roofer to ask about the plans, the pitch and the framer's timeline before giving a number. Roof Installation done right starts with the material matching the slope, the underlayment matched to the climate and a tie-in plan for any existing roof. Done that way, the roof goes on once, matches the manufacturer's install specs and gets registered correctly from the start.
On new construction the roofer is one trade among many, so timing and specs matter as much as workmanship.
Most general contractors and construction lenders want a certificate of insurance on file before the roofer starts. The contractors we route you to are licensed and insured independent businesses. Request the certificate, confirm the license with your local office and check who is listed on the roofing permit or if it rides on the building permit.
Open sheathing is a countdown. Once you are on the line, the dispatcher connects you with a nearby contractor who does new-construction work, often for a site visit within days, depending on contractor availability. If the trusses are already set and weather is coming, the dispatcher will flag it so a quick underlayment dry-in can be discussed.
A good new-build quote is tied to the plans: squares from the roof plan, pitch, valley lengths, underlayment type, ice barrier, drip edge, starter, ridge vent and every penetration. For additions, the tie-in is priced as its own line, since it includes cutting back and reworking part of the existing roof.
New-construction roofers bring roof jacks and planks for steep pitches, fall-protection anchors nailed into fresh trusses, coil nailers set for the shingle maker's nailing zone and a material lift or boom delivery to land bundles on the roof. Tie-in work adds flat bars, hook blades and tin snips for opening the old roof without tearing up good shingles.
These are the install details worth asking any contractor about before work starts.
The first thing the roofer checks is the framers' sheathing. Panels should be staggered, gapped about an eighth of an inch for expansion, supported with H-clips between trusses where required and nailed on the schedule the inspector expects. Missed nails and blowouts at the truss tops get fixed now, not after the shingles are down.
Shingles are rated down to 2:12, but between 2:12 and 4:12 the underlayment has to be doubled. Below 2:12, the roofer will usually point you toward a membrane such as modified bitumen or TPO, or a metal system rated for low slope. Getting this wrong on a porch or sunroom roof is a common source of slow leaks.
To tie an addition into an existing roof, the contractor cuts back the old shingles, weaves or laps new underlayment under the old, and runs ice and water shield across the joint. Where the new roof meets a wall, step flashing goes in course by course with a kickout at the bottom. Matching shingle color on an older roof is rarely perfect, so ask to see samples.
The order matters: drip edge at the eaves sits under the underlayment, while at the rakes it goes over. A factory starter strip with its sealant line along the eave keeps the first course from lifting, and running starter up the rakes helps in wind. These are small parts, but missing them is something the shingle maker can point to later.
Open metal, closed-cut and woven valleys are the three main options, and the manufacturer instructions say which ones they accept. Closed-cut is the most common look on new homes. Open metal valleys move the most water and suit roofs where a big upper slope dumps into a smaller one. Woven valleys do not work with many thick laminated shingles.
Skylights go in with their own flashing kits or site-built curbs before shingling, not after. Plumbing vents, bath fan hoods and the furnace flue all need boots or flashing that match the pitch. The roofer should coordinate with the plumber and HVAC crew so nobody cuts a fresh hole through a finished roof.
This is the normal path from your call to a dried-in, finished Roof Installation.
Let the dispatcher know the project type, the framing progress and any inspection dates. That routes the call to a contractor who works new builds and tie-ins.
A local roofer will either walk the framed structure or review the roof plan, often within a few days depending on availability. They look at truss layout, sheathing, wall intersections and where the new roof meets the old.
The written quote lists squares, pitch, underlayment, edge metal, valleys, penetrations and tie-in work separately. The roofer also gives a target dry-in date that fits the sheathing inspection.
After dry-in and shingling, walk the roof edges with the contractor, check the tie-in and wall flashing and confirm the roofing inspection passed. The contractor explains their workmanship terms and the manufacturer's coverage in writing.
These composite examples show what new-construction and addition calls tend to look like.
A builder had a custom home framed and sheathed, but the original roofer backed out a week before dry-in. With storms in the forecast, the whole build was stuck waiting on the roof. The independent contractor routed through the line got synthetic underlayment and drip edge down within days, then came back to shingle after the sheathing inspection passed.
A homeowner added an attached garage, and water kept showing up on the drywall where the garage roof met the two-story wall. Once the siding came off, the contractor found one long bent flashing strip and no kickout, so water was running behind the siding. The fix was individual step flashing, a kickout and a reinstalled siding course.
A sunroom addition had been framed at about a 1.5:12 pitch, and the plans called for shingles to match the house. The contractor explained that asphalt shingles are not rated below 2:12 and suggested a modified bitumen cap sheet in a matching color. The homeowner chose the membrane, and the roof has stayed dry where shingles would likely have failed.
These are composite examples of the kinds of calls we route, written to show how the process works. They are not individual customer reviews.
Usually right after the sheathing is nailed off and, where required, has passed its framing or nailing inspection. The sooner underlayment goes on after that, the better, because rain swells OSB edges. Many builders book the roofer when trusses are ordered so dry-in follows sheathing by a few days.
The contractor cuts back the existing shingles a few courses, laps new underlayment under the old, adds ice and water shield across the seam and weaves new shingles into the old field. Where the addition meets a wall, step flashing goes in with a kickout at the bottom. Ask how they plan to handle color match on older shingles.
Most asphalt shingles are rated for 2:12 and steeper, and from 2:12 to 4:12 the underlayment has to be doubled. Below 2:12, plan on a low-slope membrane like modified bitumen or TPO, or a metal panel rated for that slope. Check the pitch before framing if you can, since raising it later is costly.
Shingle makers tie their coverage to their written install instructions, from the nailing line to ventilation. Some extended programs require their own starter, hip and ridge, and underlayment. Ask the roofer to confirm the system, follow the printed specs and give you the registration details once the roof is finished.
That is part of the job on new construction. Tell the dispatcher your builder's timeline so you are routed to a contractor who does new-build work. The roofer will need the sheathing done, a clear path for material delivery and coordination with the plumber and HVAC crew for vent and flue openings.
Weathered shingles rarely match brand-new ones. Bring the contractor any leftover bundles or labels from the original roof. On a separate garage or a rear addition, a close match is often fine. If it bothers you, ask about matching the roof plane that is most visible from the street.
Metal Roofing in Bucks takes calls 24/7 and routes builders, remodelers and homeowners around Fallbrook to independent roofers who do first-time installs. Who can take the job and when comes down to local contractor schedules, and you will hear that plainly on the call.
Custom homes, spec builds, room additions, detached garages, sunrooms and porch roofs all come through the line. If you are a builder with several lots, call about each one so timing can be planned around your framing schedule.
One call connects you with a local independent contractor who can walk the framing, plan the tie-in and set a dry-in date.
